Idle Control Units

Rebuilt units from Programa. $50 core included and will be refunded upon receipt of acceptable core within 30 days.

Other products in the category Intake / Fuel:

aFe Magnum Force BMW Intake Kit -- aFe Magnum Force intakes are a performance replacement for your BMW's factory airbox and air intake system. These kits are fully engineered (not just put together to fit the space available) to maximize performance gains, with no check engine . . .

Conforti Intake System -- Due to countless hours of chassis dyno research and development, this cold air kit installs in about ½ hour and easily increases both the torque and horsepower of your BMW. This kit replaces the very restrictive factory air box with a free flowing, . . .

E46 World Challenge-Spec 325i Intake System -- This intake was designed to be used in our E46 World Challenge cars and is the result of a high degree of engineering, experience, and racecar knowledge. It has been extensively tested both on the dyno and in real track situations and it is the best . . .

Race Intake - E36 -- These aluminum intake boxes were engineered with a specific volume and carefully shaped to provide the maximum power gain for our World Challenge cars. This effort resulted in 3-4 more horsepower than any other performance intake we could find to test . . .

Samco Silicone Throttle Body Boot -- The stock rubber intake boot on your BMW is a good functional piece, but leaves power on the table. The bellows design creates flow turbulence. Additionally, the common Euro HFM adaptor piece has very abrupt transitions over a short length and . . .

BMC Air Filter - Performance Panel Replacement -- BMC air filters are designed and produced by Italian Engineers to be used in extreme conditions and to give you the highest performance. Since 1996 BMC air filters have equipped some of the most important Teams in F1 and American Le Mans Series like . . .

ITG/Conforti Replacement Filters -- Replacement ITG filter for the Conforti BMW intake kits. Available in either 3" or 3.5" versions.

ITG No Toil Oil - Cleaning System -- Service kit for the ITG foam filters used in Conforti intake systems. Kit includes cleaning solution and oil kit. Will last for multiple cleanings.

M50 Intake Plenum -- Larger volume plenum boosts Hp on 1996+ E36/M50 Z3 cars. Not a direct fit, adaptor kit may be required for your application.

M50 Intake Plenum - USED -- Larger volume plenum boosts Hp on 1996+ E36/M50 Z3 cars. Not a direct fit, adaptor kit may be required for your application. Used plenum in good mechanical condition.

M50 Plenum Adaptor Kit -- This system is designed to retain the full function of the original 1996-2000 M52/S52 system components including factory PCV cyclone/oil separator valve. Includes new hardware, gaskets, and fuel rail cover (not pictured).

1995 M3 Stage I Kit -- For the 3.0L 1995 M3 only. This kit includes the Conforti intake and software as well as the larger HFM and adapter. Everything you need to bolt on 28HP and 22ft-lbs of torque in less than an hour. Kit includes: Conforti . . .

1995 M3 Stage II Kit -- For the 3.0L 1995 M3 only. In about one hour, you can add 40+ Hp to your car for a huge increase in performance. Kit includes: Conforti shielded cold air intake Euro HFM . . .

1995 M3 Stage III Cam Kit -- For the 3.0L 1995 M3 only. In an afternoon, you can increase your M3's power output to a whopping 300! Kit includes: Conforti shielded cold air intake Euro HFM 24# . . .

Non-ASC Intake Boot -- This boot allows you to remove the ASC throttlebody for improved intake air flow. Direct replacement. When removing the ASC system, you will need to unbolt the secondary ASC throttle body (farthest from the intake plenum). This boot is a replacement . . .

Euro HFM Adaptor -- 3.5" to 3" stepdown plastic adaptor only.

OBD I Manifold Conversion Throttle Body Adaptor -- Required when the 1992-1995 intake manifold is installed on a car using the 96+ style throttle body. This plates allows the two orings to make a proper seal. Laser cut from stainless steel, tumbled finish.

E36 Euro HFM - Mass Air Meter Only -- 3.5" version for the common E36 M3 upgrade. Includes one mass air meter only. No adaptors, hardware, or software.

Porsche 993 HFM - OBD-II Upgrade -- 3.5" version for the common 96+ E36 M3 upgrade. Includes one mass air meter only. No adaptors, hardware, or software included, which are required when upgrading.

3.5" OBD I HFM Connector Housing -- This wire housing connector allows you to plug the early model 3.5" OBD I HFM into an OBD II car. NOTE: No tech help is included with this part. Proper software is also required to make this function properly.

Bosch Fuel Injectors - 24lb -- BMW fitment, for high output applications. Custom software required. Sold as a set of 6.

Bosch Fuel Injectors - 30lb -- BMW fitment, for high output applications. Custom software required. Sold as a set of 6.

Adjustable Fuel Pressure Regulator -- This billet aluminum fuel pressure regulator allows you to precisely adjust overall fuel mixture ratios and increase pressure for better atomization. A gauge on the regulator makes adjustment easy. This complete kit includes parts to replace the . . .

E36 Fuel Starvation Kits -- Fuel starvation in E36 cars occurs in sweeping right hand turns and has a similar effect to lifting in the middle of the turn, sometimes with over 1/2 tank of fuel! Since most sweeping turns are high speed, this can have disastrous results when driving . . .

E46 Fuel Starvation Kits -- Fuel starvation in E46 cars occurs in sweeping right hand turns and has a similar effect to lifting in the middle of the turn, sometimes with over 1/2 tank of fuel! Since most sweeping turns are high speed, this can have disastrous results when driving . . .

Fuel Sample Port Kit -- Our kit uses Jiffy Tite dry break fittings for ease of use of sample port. Kit includes, all fittings, fuel line, and hose clamps for full install plus test line for fuel removal.

Idle Control Valves