VAC Billet Remote Oil Filter Block

Includes multiple sensor fittings

Purchase VAC Billet Remote Oil Filter Block

Specially designed for BMW race engines!� This piece is machined from 6061-T6 aluminum for durability and is a direct replacement for the factory oil filter housing.� Included bracket maintains alternator and power steering locations.�

Designed for use with remote filters, oil coolers, dry sumps, and Accusumps
Provides oil temp, oil pressure, and Vanos line ports
Supplied with -10 AN fittings and P/S Pump Spacers
A full two pounds lighter than factory housing
Allows for easy service of components beneath intake manifold
Simplifies plumbing of remote oil cooler in all applications

Remote filter and additional lines required, not included. Fits all 24 valve engines except M5 and M6.

Purchase VAC Billet Remote Oil Filter Block

SKU: VAC.BOFH-M50

Other products in the category Engine / Performance:

BimmerWorld/Sunbelt E36 M3 OBDII Sport Cam Kit -- The long awaited BimmerWorld OBD II cam kit, utilizing Sunbelt cams is finally available. This is the first complete kit to consistently hit the 300Hp mark - and then some! Sunbelt Performance Engines is the leading name in BMW engines for . . .

1995 M3 Stage I Kit -- For 3.0L 1995 M3 5-speed manual transmission cars only. This kit includes the best products on the market - everything you need to bolt on in an hour. Kit includes: NEW - aFe Magnum Force 3.5" intake BimmerWorld Silicone Intake Boot with integrated . . .

1995 M3 Stage II Kit -- For 3.0L 1995 M3 5-speed manual transmission cars only. This kit includes the best products on the market for a huge increase in performance. Kit includes: NEW - aFe Magnum Force 3.5" intake BimmerWorld Silicone Intake Boot with integrated . . .

1995 M3 Stage III Cam Kit -- For 3.0L 1995 M3 5-speed manual transmission cars only. In an afternoon, you can increase your M3's power output to a whopping 300!� Kit includes: Conforti shielded cold air intake . . .

1993-1995 325 / 525 Power Kit -- For 9/92 production date and up E36 325 and E34 525 cars. This kit contains a set of used M3 cams in good condition and a custom Jim Conforti chip. Worth approximately 30 Hp!

EVOsport Power Pulley Kit -- The EVOsport Power Pulley Kits are designed to under-drive the alternator(*/**), power steering pump, and water pump by 10-20%, reducing parasitic power loss to significantly increase both useable torque and horsepower. The kit includes three(***) . . .

Rogue Engineering S54 Race Pulley Set -- The ultimate track-only S54 pulley set! Rogue Engineering's 4-piece S54 race pulley set is specifically designed and engineered for dedicated track cars seeing continuous high rpm use. The pulley kit is manufactured from CNC machined 6061-T6 aluminum . . .

Sunbelt Alternator Pulley -- This pulley is biggie sized to spin your alternator slower to reduce unneeded power losses.� Like any other Sunbelt product, this pulley has been dyno tested and shows real power gains.� Your electrical system will charge starting at 2500RPM, which . . .

Sunbelt E36 M3 Sport Cams -- Sunbelt Performance Engines, the leading name in BMW engines for the SPEED World Challenge and Grand Am Cup racecars is now releasing the first product in their line of engineered components for BMW cars. The E36 M3 Sport Cam was created using the . . .

Sunbelt E36 M3 Stage 3 Sport Cams -- Race only! Sunbelt spring kit required. Intake: Seat duration = 284 degrees .050" duration = 243.5 degrees Gross lift = 0.450" Hydraulic lash = 0.004" Net lift = 0.446" Exhaust: Seat duration = 280 degrees 0.050" duration = 236.6 degrees Gross . . .

Vanos Shim -- Recommended with Sunbelt Stage 3 full race cams to limit Vanos travel. Installs in OEM Vanos unit in under an hour. Machined aluminum, fits all M50 based single-Vanos engines, including 323, 325, 328, M3 and Z3 6-cylinder.

Sunbelt M50 Race Valvespring Kit -- This custom valvespring kit goes far beyond typical "performance" spring kits. Rather than double springs or springs that are much too stiff (and add increased resistance and wear because of it), these are an engineered solution. Designed for use . . .

Schrick Camshafts - E36 M3 -- The Schrick E36 M3 cam set is a more budget friendly option for internal engine performance versus our premium Sunbelt cam programs. Schrick has been producing valve train components for BMW engines for decades and know a thing or two about optimal . . .

Active Autowerke 135/335 Front Mount Intercooler Kit -- Intake air temperature means everything in a forced induction engine. The cooler the air, the more air and fuel you can pump through the engine, making more power! And as you put more boost to the engine, or demand more performance from it, the . . .

VAC Oil Pan Baffle -- Very important for track cars. Keep the oil where it works for you - circulating through the engine. In hard driving conditions with high lateral G loads, the engine oil can collect away from the pickup, leaving your engine running at less than optimum . . .

M50 Drilled Oil Pump Nut -- These nuts have a habit of coming off in track situations, leaving you with no oil pressure and a blown engine.� This nut, pre-drilled for safety wire, is the proper solution to the problem.� A must if you track your car.� Fits all 6 cylinder E36/E46 . . .

E46/E36 Dual Pickup Oil Pan/Pump Upgrade -- Oil starvation is a threat to all tracked E46 and E36 cars, especially when subjected to high braking and cornering loads and increased RPMs. While a dip to 10psi of oil pressure (a common occurrence with even baffled pan systems, whether your . . .

E36 6-Cyl Euro Oil Cooler - Filter Housing ONLY -- Euro E36 oil filter housing assembly to allow installation of an external oil cooler. Includes filter housing (tapped properly for US engine Vanos line), filter, and gasket. Fits E36 323, 325, 328, or M3 and 6-cylinder Z3 (single Vanos).

Sunbelt E46 M3 Dry Sump Kit -- Dry sumping your engine not only provides constant oil pressure, but also frees up power due to pump efficiency. This race proven Sunbelt kit, based on a Dailey Engineering pump with an air separator, is the choice of the majority of professional . . .

Pauter Connecting Rods -- Years of hands-on experience in all types of racing and racing-related abuse has given Pauter an extremely comprehensive file on just what works on the subject of high performance connecting rods. A Pauter rod looks different for not so obvious, . . .

S54 Rod Bearing Upgrade Kit -- Unfortunately, the S54 engine used in E46 M3 and MZ3/4 cars was released with a rod bearing failure problem in earlier 2001-2003 model years.� The factory addressed the issue with a rod replacement, but there is still room on the table for a better . . .

ARP Head Stud Kit -- We use these head studs on every engine we build and race because in heavy use applications, stock parts do not get the job done. Simply stated, there�s not a better stud setup on the market today. For openers, ARP Head Stud Kits use a premium grade . . .

ARP Main Stud Kit -- There are many important reasons to use ARP main stud kits, including the elimination of main cap walk and fretting, as well as protecting the threads in your engine block. The studs are manufactured in our own factory using the best materials, . . .

ARP Rod Bolt Kit -- ARP Pro Series connecting rod bolts are precision CNC-machined to exacting specifications and designed for optimum reliability. They are heat-treated and threads are rolled to provide up to ten times more fatigue strength. This makes them far superior . . .

BimmerWorld E36/E46 (also E30 318is and E9X M3) Performance/Track Engine Mounts -- This performance engine mount set is the most economical, durable, and effective set on the market.� Similar to the $800 Group N BMW engine mounts, these mounts are solid to significantly reduce engine movement under heavy G loads.� Made using OEM . . .

Increased Durometer E30 325 Engine Mount Set -- If you drive your E30 325 3 Series hard you can take advantage of these increased durometer rubber engine mounts. These mounts are ideal for street cars that see some track time since they do not increase NVH. Great for dedicated driving school . . .

BimmerWorld 3 Series Solid Engine/Transmission Mounts -- These engine mounts have undergone FEA and are CAD/CAM manufactured to eliminate any weak points and provide a solid foundation for your powertrain for zero weight transfer or torque movement. Engine mounts are 5mm shorter and transmission mounts are . . .

Solid Engine/Transmission Mounts - E30 M3 -- Non-solid engine and transmission mounts allow you car's driveline to shift with loads, meaning more slop in handling and power delivery and potential to over-rev the engine due to a moving shift pattern. CNC machined from strong 6061 T6 billet aluminum. . . .

Aluminum Fluid Catch Can -- This catch can, machined from T6061 aluminum, give you the ultimate in flexibility. Suggested for use with coolant, engine breathers, transmission/differential, etc. Do not mix fluids - a separate catch can should be used for coolant . . .

Starter With Threaded Holes -- This Bosch rebuilt starter is the best thing that ever happened to your transmission/clutch job!�� Two of the most difficult parts to get to are the starter bolts.� And in most E36 cars, these bolts have nuts on the other side of the starter that you . . .

Bosch 413 ECU - Engine Computer -- All of our used computers are tested before sending. This is the Bosch 413 computer - the universal computer to control a single vanos M50 based engine, including 93+ 325, 3.0L E36 M3, 3.2L E36 M3, and -98 2.8L. This is a computer only and not a . . .