Rogue Engineering RACEBRACE Strut Tower Brace

Reinforced webbed design

Purchase Rogue Engineering RACEBRACE Strut Tower Brace

What does a strut brace (aka stress bar or strut bar) do?
The concept of a strut bar is intended on reducing the flex between the front strut towers during hard cornering loads. By reducing this flex, it allows suspension points to remain undisturbed, allowing for the suspension to do it's job properly. This often gives the drive a feeling of increased stability and improved turning response, when in reality, the suspension is reacting as designed.

Who can benefit from a strut bar?
For those that may believe a strut bar is only for "track cars" or "racecars", it is also street driven vehicles that benefit from a properly engineered strut tower bar. Whereas anyone can appreciate the ability for a front suspension to remain constant at all times, other benefits include support of the factory strut towers from "mushrooming". These generally occurs if the vehicle hits large potholes, causing the suspension to compress completely, and then damaging the rim. However, its not only the rim that takes the hit, but the shock tower as well. Over time, if left unprotected, it can cause expensive sheet metal damage.

What to look for in a strut tower brace?
When looking at a strut tower brace to give you the most benefit, it should have the following features:

Sufficient protection of the strut tower top (to prevent "mushrooming")

Center bar with minimal bends or kinks (straighter is stiffer!)

Provide adequate underhood clearance (so not to dimple the hood)

Allow for suspension changes (for those that frequent the track)

Even BMW applied many of these traits to their own strut tower braces when they offered them. For the E36 and E46 models, both used cast aluminum strut tower plates and matched them to tubular steel center bars.

The Rogue Engineering RACEBRACE was designed as an alternative offering to the BMW Motorsport factory strut tower brace, which is no longer available. This item was standard equipment on the 1995 BMW M3 GT (350 produced, for Europe only) as well as the 1995 BMW M3 Lightweight (US market). This well engineered brace utilized cast aluminum end plates and a adjustable steel center bar. Frequently sold for more than $500 when available, these rare parts easily fetch $600-$700 on the used market. Unfortunately, this bar did not fit ASC+T vehicles.

RACEBRACE Features and Benefits

Lightweight tubular steel bars are 100% TIG welded to high strength steel plates and powdercoated black for a durable finish.

The multiple bar configuration, with center support bars, resist twisting and bending of the front chassis. Although it does not bolt to the firewall, the bar's multiple tubes resist bending and twisting in multiple planes (when compared to strut braces that use only flat bars).

Fits all 6-clyinder 1992-1999 E36 models, including those equipped with ASC+T. E46 model fits all E46 6-clyinder including 2001-2006 M3.

Open tower design allows for easy access to adjustable camber plates and shock adjustments.

Designed to offer adequate clearance over the engine components as well as underhood clearance. This is especially important in E36 coupes, as the underhood clearance is the lowest of all of the E36 models. Other strut tower braces will either put too much pressure in the hood release lever or worse, dimple the hood.

Strut tower offers full 360° support, completely covering the strut tower area. This can prevent costly sheet metal damage "mushrooming" from potholes, especially with lowered cars.

Removal of the strut brace takes only minutes with simple hand tools. Adjustments to suspension camber/caster plates can be made without removal of the bar.
At only 6.9 lbs. (E36 model), it is designed to withstand the rigors of extreme track use.

Installation Notes & FAQ

On the E36 version, our RACEBRACE does fit those with the rather short studs of TC Kline camber plates.

On our E46 version, the RACEBRACE is designed with aftermarket, adjustable camber plates in mind. For those using stock strut mounts, modified by removing the alignment pin and adjusting the suspension, the RACEBRACE has been designed to have its plates in the factory center position. For those looking for to use our E46 RACEBRACE and a little more camber on the street, use of fixed camber plates will allow both to be accomplished.

Installation for those with stock strut mounts is a matter of minutes. A typical install for an E36 is less than 10 minutes with hand tools.

For E36 models with M50/S50 engines with oil fill caps towards the firewall, the brace does not interfere with the removal of the cap. Use of a funnel is recommended for spill-free oil additions.

Purchase Rogue Engineering RACEBRACE Strut Tower Brace

Other products in the category Suspension / Steering / Miscellaneous Performance:

NEW - "Eyeball Arms" Control Arm Bushings - E46 -- Similar to the now famous E30/E36 model bushings made by Treehouse Racing, these bushing parts take the common performance control arm bushing to the next level. Made of precision CNC machined steel with a self-lubricating nylon-moly bushing, these . . .

"Eyeball Arms" Control Arm Bushings - E30 and E36 -- These arms, made by Treehouse Racing take the common performance control arm bushing to the next level. Made of precision CNC machined steel with a self-lubricating nylon-moly bushing, these arms eliminate suspension geometry movement under cornering . . .

E30/E28/E24 Fixed Camber Plates -- Adds 1.25 degrees of negative camber. Retains stock upper strut mount, or use crash mounts for 0.5 deg more camber. Steel construction with welded studs. Fits all E30 3 Series, E24 6 Series, and E28 5 Series cars.

Ground Control E36 M3 Street Spring Camber Plates -- A work of art, carved from a single piece of billet aluminum. Fits entirely within the stock reinforcements, and is adjustable through a range of 0.5 to -2.6, and can be reversed for zero camber like the stock 96-99 M3. No bearings, and is rebuildable . . .

Adjustable Street Spring Camber Plates -- These CNC machined aluminum camber plates go on top of your stock upper strut mounts to add an additional 1.25deg of negative camber. Slide adjustment means you can adjust them for both street and track settings. One pair included, DOES NOT fit . . .

Adjustable Camber/Castor Plates - Hybrid Mount, E46 M3 with Stock Springs -- True race quality castor/camber plate that won't rattle you senseless on the street! Manufactured by Ground Control, these unique hybrid plates are slotted for independent adjustment of both camber and castor - just like our race plates. Features . . .

Adjustable Camber/Castor Plates - Soft Mount -- True race quality castor/camber plate that won't rattle you senseless on the street! Manufactured by Ground Control, these unique hybrid plates are slotted for independent adjustment of both camber and castor - just like our race plates. Features . . .

Adjustable Camber/Castor Plates - E30 Street Spring/Spec E30 -- True race quality castor/camber plate for use with stock style springs for E30 3 Series cars. Manufactured by Ground Control, these plates are slotted for independent adjustment of both camber and castor. Features like a CNC machined aluminum . . .

E36 Front Camber Shim Kit -- If you need more negative front camber in your E36, adding these shims is one of the easiest methods. These shims are precision cut from 6061 aluminum for strength and weight. Full shim kit includes 0.030", 0.060", 0.120" shim plates which can be used . . .

Adjustable Swaybars - Racing Dynamics -- Racing Dynamics swaybars are fully adjustable both front and rear (many brands are adjustable on the rear only on older cars) and are sized properly to work with both street and stiffer race suspensions. Complete kits include urethane bushings and . . .

Ground Control Slide Adjustable Swaybars -- These swaybars manufactured by Ground Control to our specs are the only tubular, fully adjustable race bars on the market. Additionally, they are available separately or in pairs to compliment your individual suspension requirements and fit the SCCA . . .

E30 25mm Tubular Front Swaybar -- This bar has three holes for adjustment and includes adjustable swaybar links and brackets. Reduces body roll while using lighter spring rates. Uses M3 style links - must attach to strut housing, not control arm.

Ireland Spec E30 Swaybars -- This is one of the most complete sway bar kits you will find on the market. It comes complete with all reinforcements for mounting tabs, spherical end-links, and billet mounts with urethane bushings. The front is a non adjustable 22mm bar per Spec E30 . . .

M3 Swaybar Endlink Assemblies -- The highest quality available. The rod ends used for our endlink assemblies are made specifically for our kit. We have specified to the bearing manufacturer our requirements for high angularity and preloaded Teflon liners for a long service life. If . . .

Strut Tower Brace - Racing Dynamics -- These strut tower braces made by Racing Dynamics are an excellent way to reduce strut tower flex and stress on the subframe. All are made of extruded aluminum oval tubes with an internal reinforcing rib that is heat treated and mandrel bent.

Sparco Front Strut Tower Bar - Steel -- This front strut tower bar from Sparco is made from tubular steel for a very strong and effective design. Note: This bar will fit the E36 Ti Compact chassis only if the battery is relocated. The E30 bar will not fit the 318is with out modification. . . .

BMW Motorsport X Brace

Ground Control 3 Series Rear Shock Mounts - Urethane/Al -- Stock, or even heavy-duty stock rear shock mounts (RSMs), are high wear items on BMW 3 Series cars. These mounts cannot endure the stresses caused by aggressive driving and stiff shock valving. Additionally, when RSMs flex considerably, you are losing . . .

Rogue Engineering 3 Series Rear Shock Mounts -- Say goodbye to rear end clunks! With the introduction of the Rogue Engineering Rear Shock Mounts, you have a high quality, rebuildable, easily serviceable rear shock mount. Fits the following vehicles: All E30, including M3 All E36, . . .

Rear Shock Tower Brace - Racing Dynamics -- Designed with chassis stiffness and ease of mounting in mind, these aluminum braces are hard to beat. End pieces are CNC machined for optimum quality.

E36/46 Rear Toe Spacers -- These urethane reinforcements fill the empty void space in the E36 and E46 rear toe bushing, which both stiffens the suspension slightly and is a preventative measure against failure of the weak factory bushings. Quick install! Not for use with Powerflex . . .

Reinforced Rear Lower Control Arm -- The rear lower control arms are one of the weaker items on your BMW's rear suspension. These quality Lemfoerder arms have been reinforced on both sides to strengthen the flimsy stock arm. Fits all E36 and E46 3 Series, except 318ti. Legal in BMW . . .

Adjustable Aluminum Rear Lower Control Arms - E36/E46/Z4 -- Made of 7075-T6 aluminum (commonly used in high-strength applications such as aircraft fittings and brake pistons), these lightweight adjustable rear arms are perfect for track cars and street cars alike. These arms address several issues: Performance . . .

Adjustable Steel Rear Lower Control Arms - E36/E46/Z4 -- Whether you need to correct you alignment for track use or after lowering your car, or need a beefier part to replace your factory stamped steel lower arms, our steel pieces do the job! When a BMW is lowered, it can cause additional and unwanted . . .

Ground Control E36/E46 Street/Track Adjustable Rear Lower Control Arm -- Chrome moly racing rear control arm, designed to suit 2006 BMWCCA rules changes. Urethane bushing, with grease fitting, turnbuckle adjustable to achieve any needed rear camber - far beyond the range of adjustability for the factory arm. Double sheer . . .

Rear Camber/Toe Adjustment Kit - E30, Z3, 318ti -- Whether you need to get your modified car back to stock alignment specs or you need adjustable suspension geometry on your track car, this kit will get you there. When the E30 rear suspension (includes Z3 and E36 318ti) is lowered, camber and toe . . .

E36 Front Strut Tower Reinforcement Plates -- The front strut towers have a tendency to tear, especially when the car uses camber plates. These plates fit all E36 models, 1992-1999 except 1996-1999 M3. Bolt-on fitment.

E30 Front Subframe Reinforcement Kit -- The front subframe is highly stressed and will crack quickly due to vibration on a tracked E30 car. This reinforcement kit consists of two precision cut plates to be installed as a preventative measure, but they can be used to repair a damaged subframe . . .

E30 Front Swaybar Reinforcement Kit -- Precision cut steel plate to reinforce the weak factory front swaybar attachment point. Fits all non-M E30 3 Series cars. Welding required.

E36/E46 Front Subframe Reinforcement Kit -- The front subframe is highly stressed and will crack quickly on a heavily tracked E36 or E46 car. This reinforcement kit consists of two precision cut plates to be installed as a preventative measure, but they can be used to repair a damaged subframe . . .

Rear Shock Tower Reinforcement Plates -- The rear shock towers are a known weak spot on all 1984-2005 3 Series cars. The metal in this area fatigues and begins to crack, caused by the common stock mount failure or the added stresses of a performance suspension. Our plates can be bolted . . .

E36 Rear Subframe/Chassis Reinforcement Kit -- The rear chassis at the point the rear subframe attaches is a failure point on heavily tracked E36 cars. All M3s have reinforcement plates welded in from the factory to solve this problem. But if you track your non-M E36, chances are at some point you . . .

E36 Rear Swaybar Reinforcement Kit -- The use of a heavier rear swaybar puts a bending load on the stock rear subframe that it was not designed to take. Our reinforcement kit will support the rear subframe area to better accept this loading without deformation. Two piece kit, welding . . .

E36 Rear Trailing Arm Pocket Reinforcement Kit -- This location on the E36 chassis can fatigue over time, allowing the front mounting point of the rear trailing arm to tear out of the car chassis with often fantastic results. This 6-piece reinforcement plate kit reinforces the stock pocket bungs . . .

E36/E46 Rear Lower Control Arm Reinforcement Kit -- The stock rear lower control arms (or "salad tongs") are just that - fairly flimsy tong shaped stamped steel pieces. Our reinforcement plates weld on to significantly increase the strength of these parts. Welding required or finished modified . . .

Electric Race Power Steering System -- This "smart pump" reduces losses by engaging the power steering pump only when it is required, not full time like a factory belt-driven pump. Pushing up to 73 bars of pressure, this pump can accommodate even heavier sedans with big rubber. This system . . .